InTENSity 5000 Hybrid Digital and Analog Tens Unit

Brief Overview:

The InTENSity™ 5000 Hybrid Digital and Analog Tens Unit combines the ease of traditional analog knobs with the beauty of LED display technology to give you the feedback that you need to get the right therapy at the right time.

The InTENSity™ 5000 Hybrid and Analog Tens Unit combines the ease of traditional analog knobs with the beauty of LED display technology to give you the feedback that you need to get the right therapy at the right time.

The InTENSity™ 5000 Hybrid Digital and Analog Tens Unit includes FIVE modes of operation:

• Burst Mode (B): Bursts occur twice every second. Pulse width (adjustable), pulse rate=100 Hz, Burst rate=0.5 Hz

• Normal Mode (N): The pulse rate and pulse width are adjustable. It generates continuous stimulation based on the setting value.

• Modulation 1 Mode (M1): Modulation 1 mode is a pulse width modulation. The pulse width is automatically varied in a cycle pattern over an interval of nominally 10 seconds. Pulse width increase over a period of 5 seconds from 30 us to the control setting value, then decreases over a 5 second period to its original value.

• Modulation 2 Mode (M2): Modulation 2 mode is a pulse rate modulation. The pulse rate is automatically varied in a cycle pattern over an interval of nominally 10 seconds. Pulse rate decreases over a period of 5 seconds from the control setting value to a value which is 40% less, then increases over a 5 second period to its original value. They cycle is then repeated.

• SD Mode (SD): The SD (Strength-Duration) mode consists of automatic modulation intensity and pulse width in 70% range. The intensity is always while the pulse width is decreasing and vice versa. The intensity is decreased by 70% while the pulse width is increased by 70% in 5 seconds. In the next 5 seconds, the intensity is increased by 70% while the pulse width is decreased by 70%. Total cycle time is 10 seconds. Pulse rate (2~150Hz) and pulse width (30~260uS) are fully adustable.

TENS Unit Stimulation – stands for Transcutaneous Electrical Nerve Stimulation. Pain, whether chronic (long-term) or acute (short-term, often from surgery or trauma), can be relieved through a variety of methods including drugs, topical ointments, surgery, and electrical stimulation. TENS devices deliver mild electrical pulses through the skin to stimulate the cutaneous (surface) and afferent (deep) nerves to help control pain. Unlike drugs or topical ointments, TENS do not have any known side effects.

• InTENSity™ 5000 Hybrid Digital and Analog Tens Unit

· Timer

• Lead Wires

• Four Self-Stick Hypoallergenic Disposable Electrodes

• Hard Plastic Case

• 9-volt alkaline battery

• Instruction Booklet

• Two Year Warranty

• Channel: Dual Channel, isolated between channels

• Power Supply: One 9-volt battery

• Pulse Amplitude: Adjustable, 0-80 mA peak into 500 ohm load each channel

• Pulse Rate: Adjustable, from 2 to 150 Hz

• Burst rate: 0.5Hz (Burst mode)

• Pulse Width: Adjustable, from 30-260 microseconds

• Voltage: 0 to 40 V (Load: 500 ohm)

• Wave Form: Mono-phase square pulse wave

• Size: 11.7 cm (L) x 6.6 cm (W) x 28.5 cm (H)

• Weight: 94 g (without battery)

• Timer: 15, 30, 60 minutes or continuous

• Burst Mode (B): Bursts occur twice every second. Pulse width (adjustable), pulse rate=100 Hz, Burst rate=0.5 Hz

• Normal Mode (N): The pulse rate and pulse width are adjustable. It generates continuous stimulation based on the setting value.

• Modulation 1 Mode (M1): Modulation 1 mode is a pulse width modulation. The pulse width is automatically varied in a cycle pattern over an interval of nominally 10 seconds. Pulse width increase over a period of 5 seconds from 30 us to the control setting value, then decreases over a 5 second period to its original value.

• Modulation 2 Mode (M2): Modulation 2 mode is a pulse rate modulation. The pulse rate is automatically varied in a cycle pattern over an interval of nominally 10 seconds. Pulse rate decreases over a period of 5 seconds from the control setting value to a value which is 40% less, then increases over a 5 second period to its original value. They cycle is then repeated.

• SD Mode (SD): The SD (Strength-Duration) mode consists of automatic modulation intensity and pulse width in 70% range. The intensity is always while the pulse width is decreasing and vice versa. The intensity is decreased by 70% while the pulse width is increased by 70% in 5 seconds. In the next 5 seconds, the intensity is increased by 70% while the pulse width is decreased by 70%. Total cycle time is 10 seconds. Pulse rate (2~150Hz) and pulse width (30~260uS) are fully adustable.

INTENSITY Twin Stim III - Digital Tens and Muscle Stimulator | INTENSITY Select Combo Digital Tens-EMS-Interferential-Microcurrent | Compex Sport Elite Muscle Stimulator | Compex Performance US Muscle Stimulator | MPO Wireless 10 Mode Combo TENS and EMS System | MPO-2500 Ultra Russian Muscle Stimulator | MPO IF-4000 Ultra Interferential System with Russan Stimulation | Quattro True Interferential Four Isolated Channel Clinical System | Quattro Four Channel Clinical 3 Mode Muscle Stimulation System | INTENSITY Twin Stim III - Digital Tens and Muscle Stimulator